Array ( [0] => {{short description|Passive electrical component providing electrical resistance}} [1] => {{pp|small=yes}} [2] => {{Infobox electronic component [3] => | component = Resistor [4] => | image = [[File:Electronic-Axial-Lead-Resistors-Array.png|250px]] [5] => | caption = An array of axial-lead resistors [6] => | type = [[Passivity (engineering)|Passive]] [7] => | working_principle = [[Electric resistance]] [8] => | invented = [9] => | first_produced = [10] => | symbol = [[File:IEEE 315-1975 (1993).2.1.1.a.svg|100px]] [[File:IEEE 315-1975 (1993) 2.1.1.b.svg|100px]] [11] => | symbol_caption = IEEE schematic symbols [12] => }} [13] => [14] => [[File:Carbon and ceramic resistors of different power ratings.jpg|thumb|upright=1.2|right|Various resistor types of different shapes and sizes]] [15] => [16] => A '''resistor''' is a [[passivity (engineering)|passive]] [[terminal (electronics)|two-terminal]] [[electronic component|electrical component]] that implements [[electrical resistance]] as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to [[Voltage divider|divide voltages]], [[Biasing|bias]] active elements, and terminate [[transmission line]]s, among other uses. High-power resistors that can dissipate many [[watt]]s of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for [[electric generator|generators]]. [17] => Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity. [18] => [19] => Resistors are common elements of [[electrical network]]s and [[electronic circuit]]s and are ubiquitous in [[Electronics|electronic equipment]]. Practical resistors as discrete components can be composed of various compounds and forms. Resistors are also implemented within [[integrated circuits]]. [20] => [21] => The electrical function of a resistor is specified by its resistance: common commercial resistors are manufactured over a range of more than nine [[orders of magnitude]]. The nominal value of the resistance falls within the [[Engineering tolerance#Electrical component tolerance|manufacturing tolerance]], indicated on the component. [22] => [23] => ==Electronic symbols and notation== [24] => {{Main article|Electronic symbol|RKM code}} [25] => [26] => Two typical [[schematic diagram]] symbols are as follows: [27] => [28] => File:Resistor, Rheostat (variable resistor), and Potentiometer symbols.svg| [[ANSI]]-style: (a) resistor, (b) rheostat (variable resistor), and (c) potentiometer [29] => File:Resistor_symbol_IEC.svg|[[International Electrotechnical Commission|IEC]] resistor symbol [30] => [31] => [32] => The notation to state a resistor's value in a circuit diagram varies. [33] => [34] => One common scheme is the [[RKM code]] following [[IEC 60062]]. Rather than using a [[decimal separator]], this notation uses a letter loosely associated with SI prefixes corresponding with the part's resistance. For example, ''8K2'' as part [[marking code]], in a [[circuit diagram]] or in a [[bill of materials]] (BOM) indicates a resistor value of 8.2 kΩ. Additional zeros imply a tighter tolerance, for example ''15M0'' for three significant digits. When the value can be expressed without the need for a prefix (that is, multiplicator 1), an "R" is used instead of the decimal separator. For example, ''1R2'' indicates 1.2 Ω, and ''18R'' indicates 18 Ω. [35] => [36] => ==Theory of operation== [37] => [[File:ResistanceHydraulicAnalogy2.svg|thumb|upright=1.8|right|The [[hydraulic analogy]] compares electric current flowing through circuits to water flowing through pipes. When a pipe (left) is clogged with hair (right), it takes a larger pressure to achieve the same flow of water. Pushing electric current through a large resistance is like pushing water through a pipe clogged with hair: It requires a larger push ([[voltage]]) to drive the same flow ([[electric current]]).{{cite web|author=Harder, Douglas Wilhelm |title=Resistors: A Motor with a Constant Force (Force Source)|url=https://ece.uwaterloo.ca/~dwharder/Analogy/Resistors/|publisher=Department of Electrical and Computer Engineering, University of Waterloo|access-date=9 November 2014}}]] [38] => [39] => ===Ohm's law=== [40] => {{Main article|Ohm's law}} [41] => [42] => The behaviour of an ideal resistor is described by [[Ohm's law]]: [43] => [44] => V=I \cdot R. [45] => [46] => Ohm's law states that the [[voltage]] (V) across a resistor is proportional to the [[Electric current|current]] (I) passing through it, where the constant of proportionality is the resistance (R). For example, if a 300-[[ohm]] resistor is attached across the terminals of a 12-volt battery, then a current of 12 / 300 = 0.04 [[ampere]]s flows through that resistor. [47] => [48] => The [[Ohm (unit)|ohm]] (symbol: [[Ω]]) is the [[International System of Units|SI]] unit of [[electrical resistance]], named after [[Georg Simon Ohm]]. An ohm is equivalent to a [[volt]] per [[ampere]]. Since resistors are specified and manufactured over a very large range of values, the derived units of milliohm (1 mΩ = 10−3 Ω), kilohm (1 kΩ = 103 Ω), and megohm (1 MΩ = 106 Ω) are also in common usage.{{cite book | author=[[American Radio Relay League]] (ARRL) | title =ARRL Handbook for Radio Communications | publisher =American Radio Relay League |isbn=978-1-62595-139-7 | date=2021 | edition =98| chapter = Fundamental Theory—Circuits and Components}}{{cite book | url=https://archive.org/details/arrl_1968_handbook |editor=Doug DeMaw | title =Radio Amateurs Handbook | publisher =American Radio Relay League |date=1968 | edition=45 |chapter = Electrical Laws and Circuits —Resistance}}{{rp|p.20}} [49] => [50] => ===Series and parallel resistors{{anchor|Series_and_parallel_circuits}}=== [51] => {{anchor|series|Series}} [52] => {{Main article|Series and parallel circuits}} [53] => [54] => The total resistance of resistors connected in series is the sum of their individual resistance values.{{clear|left}} [55] => [[File:resistors in series.svg|alt=Circuit diagram of several resistors, labelled R1, R2 ... Rn, connected end to end]] [56] => [57] => R_\mathrm{eq} = \sum_{i=1}^n R_i = R_1 + R_2 + \cdots + R_n. [58] => [59] => {{anchor|parallel|Parallel}} [60] => The total resistance of resistors connected in parallel is the reciprocal of the sum of the reciprocals of the individual resistors.{{rp|p.20ff}}{{clear|left}} [61] => [[File:resistors in parallel.svg|alt=Circuit diagram of several resistors, labelled R1, R2 ... Rn, side by side, both leads of each connected to the same wires]] [62] => [63] => R_\mathrm{eq} = \left(\sum_{i=1}^n\frac{1}{R_i}\right)^{-1} = \left({1\over R_1} + {1\over R_2} + {1\over R_3} + \dots + {1\over R_n}\right)^{-1} [64] => [65] => [66] => For example, a 10 ohm resistor connected in parallel with a 5 ohm resistor and a 15 ohm resistor produces {{sfrac|1/10 + 1/5 + 1/15}} ohms of resistance, or {{sfrac|30|11}} = 2.727 ohms. [67] => [68] => A resistor network that is a combination of parallel and series connections can be broken up into smaller parts that are either one or the other. Some complex networks of resistors cannot be resolved in this manner, requiring more sophisticated circuit analysis. Generally, the [[Y-Δ transform]], or [[Equivalent impedance transforms#2-terminal, n-element, 3-element-kind networks|matrix methods]] can be used to solve such problems.Farago, P.S. (1961) ''An Introduction to Linear Network Analysis'', pp. 18–21, The English Universities Press Ltd.{{cite journal|doi=10.1088/0305-4470/37/26/004|title=Theory of resistor networks: The two-point resistance|year=2004|author=Wu, F. Y.|journal=Journal of Physics A: Mathematical and General|volume=37|issue=26|pages=6653–6673|arxiv=math-ph/0402038|bibcode=2004JPhA...37.6653W|s2cid=119611570}}{{cite book|author1=Wu, Fa Yueh|author2=Yang, Chen Ning |title=Exactly Solved Models: A Journey in Statistical Mechanics : Selected Papers with Commentaries (1963–2008)|url=https://books.google.com/books?id=H-k8dhB7lmwC&pg=PA489|date=2009|publisher=World Scientific|isbn=978-981-281-388-6|pages=489–}} [69] => [70] => ===Power dissipation=== [71] => [[File:Resistor warming thermal video.webm|thumb|Resistor warming caused by electrical current captured by thermal camera]] [72] => At any instant, the power ''P'' (watts) consumed by a resistor of resistance ''R'' (ohms) is calculated as: [73] => [74] => P = I V = I^2 R = \frac{V^2}{R} [75] => [76] => where ''V'' (volts) is the voltage across the resistor and ''I'' (amps) is the [[Ampere|current]] flowing through it. Using [[Ohm's law]], the two other forms can be derived. This power is converted into heat which must be dissipated by the resistor's package before its temperature rises excessively.{{rp|p.22}} [77] => [78] => Resistors are rated according to their maximum power dissipation. Discrete resistors in solid-state electronic systems are typically rated as {{frac|10}}, {{frac|8}}, or {{frac|4}} watt. They usually absorb much less than a watt of electrical power and require little attention to their power rating. [79] => [80] => [[File:Danotherm HS50 power resistor.jpg|thumb|An aluminium-encased power resistor rated for dissipation of 50 W when mounted on a heat-sink]] [81] => Power resistors are required to dissipate substantial amounts of power and are typically used in power supplies, power conversion circuits, and power amplifiers; this designation is loosely applied to resistors with power ratings of 1 watt or greater. Power resistors are physically larger and may not use the preferred values, color codes, and external packages described below. [82] => [83] => If the average power dissipated by a resistor is more than its power rating, damage to the resistor may occur, permanently altering its resistance; this is distinct from the reversible change in resistance due to its [[temperature coefficient]] when it warms. Excessive power dissipation may raise the temperature of the resistor to a point where it can burn the circuit board or adjacent components, or even cause a fire. There are flameproof resistors that will not produce flames with any overload of any duration. [84] => [85] => Resistors may be specified with higher rated dissipation than is experienced in service to account for poor air circulation, high altitude, or high [[operating temperature]]. [86] => [87] => All resistors have a maximum voltage rating; this may limit the power dissipation for higher resistance values.{{cite web |url=https://seielect.com/news/20170821_-_Resistor_Data_Sheet_Information.pdf |title=Specifications and How to Interpret Them|publisher= Stackpole Electronics|access-date=July 6, 2021}} For instance, among {{frac|4}} watt resistors (a very common sort of [[through-hole technology|leaded]] resistor) one is listed with a resistance of 100 MΩ{{Cite web |title=Through Hole Resistor, 0.1 Gohm, RGP Series, 250 mW, ± 5%, Axial Leaded, 750 V |url=https://nl.farnell.com/te-connectivity/rgp0207chj100m/res-100m-5-250mw-axial-thick-film/dp/2805251 |url-status=dead |archive-url=https://web.archive.org/web/20210709190647/https://nl.farnell.com/te-connectivity/rgp0207chj100m/res-100m-5-250mw-axial-thick-film/dp/2805251 |archive-date=2021-07-09 |access-date=2023-10-07 |website=nl.farnell.com}} and a maximum rated voltage of 750 V. However even placing 750 V across a 100 MΩ resistor continuously would only result in a power dissipation of less than 6 mW, making the nominal {{frac|4}} watt rating meaningless. [88] => [89] => [[File:USSR power resistor VZR 12W.JPG|thumb|VZR power resistor 1.5 kΩ 12 W, manufactured in 1963 in the Soviet Union]] [90] => [91] => == Nonideal properties == [92] => Practical resistors have a series [[inductance]] and a small parallel [[capacitance]]; these specifications can be important in high-frequency applications. In a [[low-noise amplifier]] or [[pre-amp]], the [[Noise (electronics)|noise]] characteristics of a resistor may be an issue. [93] => [94] => In some precision applications, the [[temperature coefficient]] of the resistance may also be of concern. [95] => [96] => The unwanted inductance, excess noise, and temperature coefficient are mainly dependent on the technology used in manufacturing the resistor. They are not normally specified individually for a particular family of resistors manufactured using a particular technology.A family of resistors may also be characterized according to its ''critical resistance.'' Applying a constant voltage across resistors in that family below the critical resistance will exceed the maximum power rating first; resistances larger than the critical resistance fail first from exceeding the maximum voltage rating. See {{cite book |author=Middleton, Wendy |author2=Van Valkenburg, Mac E. |title=Reference data for engineers: radio, electronics, computer, and communications |edition=9 |publisher=Newnes |year=2002 |isbn=0-7506-7291-9 |pages=5–10}} A family of discrete resistors may also be characterized according to its form factor, that is, the size of the device and the position of its leads (or terminals). This is relevant in the practical manufacturing of circuits that may use them. [97] => [98] => Practical resistors are also specified as having a maximum [[Power (physics)|power]] rating which must exceed the anticipated power dissipation of that resistor in a particular circuit: this is mainly of concern in power electronics applications. [99] => Resistors with higher power ratings are physically larger and may require [[heat sink]]s. In a high-voltage circuit, attention must sometimes be paid to the rated maximum working voltage of the resistor. While there is no minimum working voltage for a given resistor, failure to account for a resistor's maximum rating may cause the resistor to incinerate when current is run through it. [100] => [101] => ==Fixed resistors== [102] => {{Main article|List of resistors}} [103] => [[File:Sil resistor.png|thumb|A single in line (SIL) resistor package with 8 individual 47 ohm resistors. This package is also known as a SIP-9. One end of each resistor is connected to a separate pin and the other ends are all connected together to the remaining (common) pin – pin 1, at the end identified by the white dot.]] [104] => [105] => ===Lead arrangements=== [106] => [[File:3 Resistors.jpg|thumb|right| Axial resistors with wire leads for through-hole mounting]] [107] => [[Through-hole]] components typically have "leads" (pronounced {{IPAc-en|l|iː|d|z}}) leaving the body "axially", that is, on a line parallel with the part's longest axis. Others have leads coming off their body "radially" instead. Other components may be [[Surface-mount technology|SMT]] (surface mount technology), while high power resistors may have one of their leads designed into the [[heat sink]]. [108] => [109] => ===Carbon composition=== [110] => [[File:Résistances anciennes annees 50.jpg|thumb|Old style "dog bone" resistors with "body, tip, dot" color code marking]] [111] => [[File:Old Radio Resistors.jpg|thumb|Three carbon composition resistors in a 1960s [[Vacuum tube|valve]] (vacuum tube) radio]] [112] => Carbon composition resistors (CCR) consist of a solid cylindrical resistive element with embedded wire leads or metal end caps to which the lead wires are attached. The body of the resistor is protected with paint or plastic. Early 20th-century carbon composition resistors had uninsulated bodies; the lead wires were wrapped around the ends of the resistance element rod and soldered. The completed resistor was painted for [[Electronic color code#Resistors|color-coding]] of its value. [113] => [114] => The resistive element in carbon composition resistors is made from a mixture of finely powdered carbon and an insulating material, usually ceramic. A resin holds the mixture together. The resistance is determined by the ratio of the fill material (the powdered ceramic) to the carbon. Higher concentrations of carbon, which is a good conductor, result in lower resistances. Carbon composition resistors were commonly used in the 1960s and earlier, but are not popular for general use now as other types have better specifications, such as tolerance, voltage dependence, and stress. Carbon composition resistors change value when stressed with over-voltages. Moreover, if internal moisture content, such as from exposure for some length of time to a humid environment, is significant, soldering heat creates a non-reversible change in resistance value. Carbon composition resistors have poor stability with time and were consequently factory sorted to, at best, only 5% tolerance.Harter, James H. and Lin, Paul Y. (1982) ''Essentials of electric circuits''. Reston Publishing Company. pp. 96–97. {{ISBN|0-8359-1767-3}}. These resistors are non-inductive, which provides benefits when used in voltage pulse reduction and surge protection applications.HVR International (ed.). [http://www.hvrint.com/SRSeries.pdf "SR Series: Surge Resistors for PCB Mounting"]. (PDF; 252 kB), 26 May 2005, retrieved 24 January 2017. Carbon composition resistors have higher capability to withstand overload relative to the component's size.Beyschlag, Vishay (2008). [https://www.vishay.com/docs/28771/basics.pdf "Basics of Linear Fixed Resistors Application Note"], Document Number 28771. [115] => [116] => Carbon composition resistors are still available, but relatively expensive. Values ranged from fractions of an ohm to 22 megohms. Due to their high price, these resistors are no longer used in most applications. However, they are used in power supplies and welding controls. They are also in demand for repair of vintage electronic equipment where authenticity is a factor. [117] => [118] => ===Carbon pile=== [119] => A carbon pile resistor is made of a stack of carbon disks compressed between two metal contact plates. Adjusting the clamping pressure changes the resistance between the plates. These resistors are used when an adjustable load is required, such as in testing automotive batteries or radio transmitters. A carbon pile resistor can also be used as a speed control for small motors in household appliances (sewing machines, hand-held mixers) with ratings up to a few hundred watts.Morris, C. G. (ed.) (1992). ''Academic Press Dictionary of Science and Technology''. Gulf Professional Publishing. p. 360. {{ISBN|0122004000}}. A carbon pile resistor can be incorporated in automatic [[voltage regulator]]s for generators, where the carbon pile controls the field current to maintain relatively constant voltage.''Principles of automotive vehicles''. United States Department of the Army (1985). p. 13 This principle is also applied in the [[carbon microphone]]. [120] => [121] => ===Carbon film=== [122] => [[File:Carbon-resistor-TR212-1.jpg|thumb|Carbon film resistor with exposed carbon spiral (Tesla TR-212 1 kΩ)]] [123] => In manufacturing carbon film resistors, a carbon film is deposited on an insulating substrate, and a [[helix]] is cut in it to create a long, narrow resistive path. Varying shapes, coupled with the [[resistivity]] of [[amorphous]] carbon (ranging from 500 to 800 μΩ m), can provide a wide range of resistance values. Carbon film resistors feature lower noise compared to carbon composition resistors because of the precise distribution of the pure graphite without binding.{{cite web|title=Carbon Film Resistor|url=http://www.resistorguide.com/carbon-film-resistor/|work= The Resistorguide|access-date=10 March 2013}} Carbon film resistors feature a power rating range of 0.125 W to 5 W at 70 °C. Resistances available range from 1 ohm to 10 megaohm. The carbon film resistor has an [[operating temperature]] range of −55 °C to 155 °C. It has 200 to 600 volts maximum working voltage range. Special carbon film resistors are used in applications requiring high pulse stability. [124] => [125] => ===Printed carbon resistors=== [126] => [[File:PCB Carbon Printed Resistor.jpg|thumb|Carbon resistors (black rectangles) printed directly onto the SMD pads on the PCB of a [[Psion Organiser]] II from 1989]] [127] => [128] => Carbon composition resistors can be printed directly onto [[printed circuit board]] (PCB) substrates as part of the PCB manufacturing process. Although this technique is more common on hybrid PCB modules, it can also be used on standard fibreglass PCBs. Tolerances are typically quite large and can be in the order of 30%. A typical application would be non-critical [[pull-up resistor]]s. [129] => [130] => ===Thick and thin film=== [131] => [[File:Laser Trimmed Precision Thin Film Resistor Network.JPG|thumb|Laser Trimmed Precision Thin Film Resistor Network from Fluke, used in the Keithley DMM7510 multimeter. Ceramic backed with glass hermetic seal cover.]] [132] => Thick film resistors became popular during the 1970s, and most [[surface-mount technology|SMD]] (surface mount device) resistors today are of this type. The resistive element of thick films is 1000 times thicker than thin films,{{cite web|title=Thick Film and Thin Film|url=http://www.digikey.com/Web%20Export/Supplier%20Content/Stackpole_738/PDF/Stackpole_ThickFilmXThinFilm.pdf|publisher=Digi-Key (SEI)|access-date=23 July 2011|archive-date=27 September 2011|archive-url=https://web.archive.org/web/20110927122203/http://www.digikey.com/Web%20Export/Supplier%20Content/Stackpole_738/PDF/Stackpole_ThickFilmXThinFilm.pdf|url-status=dead}} but the principal difference is how the film is applied to the cylinder (axial resistors) or the surface (SMD resistors). [133] => [134] => Thin film resistors are made by [[sputtering]] (a method of [[vacuum deposition]]) the resistive material onto an insulating substrate. The film is then etched in a similar manner to the old (subtractive) process for making printed circuit boards; that is, the surface is coated with a [[photoresist|photo-sensitive material]], covered by a pattern film, irradiated with [[ultraviolet]] light, and then the exposed photo-sensitive coating is developed, and underlying thin film is etched away. [135] => [136] => Thick film resistors are manufactured using screen and stencil printing processes. [137] => [138] => Because the time during which the sputtering is performed can be controlled, the thickness of the thin film can be accurately controlled. The type of material also varies, consisting of one or more ceramic ([[cermet]]) conductors such as [[tantalum nitride]] (TaN), [[Ruthenium(IV) oxide|ruthenium oxide]] ({{chem|RuO|2}}), [[Lead(II) oxide|lead oxide]] (PbO), [[bismuth ruthenate]] ({{chem|Bi|2|Ru|2|O|7}}), [[chromel|nickel chromium]] (NiCr), or [[bismuth iridate]] ({{chem|Bi|2|Ir|2|O|7}}). [139] => [140] => The resistance of both thin and thick film resistors after manufacture is not highly accurate; they are usually trimmed to an accurate value by abrasive or [[laser trimming]]. Thin film resistors are usually specified with tolerances of 1% and 5%, and with temperature coefficients of 5 to 50 [[Temperature coefficient|ppm/K]]. They also have much lower [[Resistor noise|noise]] levels, on the level of 10–100 times less than thick film resistors.{{cite web|title=Thin and Thick film|url=http://www.resistorguide.com/thin-and-thick-film/|website=resistorguide.com|publisher=resistor guide|access-date=3 December 2017}} Thick film resistors may use the same conductive ceramics, but they are mixed with [[sintered]] (powdered) glass and a carrier liquid so that the composite can be [[screen-printing|screen-printed]]. This composite of glass and conductive ceramic (cermet) material is then fused (baked) in an oven at about 850 °C. [141] => [142] => When first manufactured, thick film resistors had tolerances of 5%, but standard tolerances have improved to 2% or 1% in the last few decades.{{timeframe|date=December 2021}} Temperature coefficients of thick film resistors are typically ±200 or ±250 ppm/K; a 40-[[kelvin]] (70 °F) temperature change can change the resistance by 1%. [143] => [144] => Thin film resistors are usually far more expensive than thick film resistors. For example, SMD thin film resistors, with 0.5% tolerances and with 25 ppm/K temperature coefficients, when bought in full size reel quantities, are about twice the cost of 1%, 250 ppm/K thick film resistors. [145] => [146] => ===Metal film=== [147] => A common type of axial-leaded resistor today is the metal-film resistor. Metal Electrode Leadless Face ([[MELF Electronic Components|MELF]]) resistors often use the same technology. [148] => [149] => Metal film resistors are usually coated with nickel chromium (NiCr), but might be coated with any of the cermet materials listed above for thin film resistors. Unlike thin film resistors, the material may be applied using different techniques than sputtering (though this is one technique used). The resistance value is determined by cutting a helix through the coating rather than by etching, similar to the way carbon resistors are made. The result is a reasonable tolerance (0.5%, 1%, or 2%) and a temperature coefficient that is generally between 50 and 100 ppm/K.{{cite web [150] => | url = http://www.kennethkuhn.com/students/ee431/text/ee431lab3.pdf [151] => | title = Measuring the Temperature Coefficient of a Resistor [152] => | access-date = 2010-03-18 [153] => | author = Kuhn, Kenneth A. [154] => | archive-date = 2016-03-04 [155] => | archive-url = https://web.archive.org/web/20160304081455/http://www.kennethkuhn.com/students/ee431/text/ee431lab3.pdf [156] => | url-status = dead [157] => }} Metal film resistors possess good noise characteristics and low non-linearity due to a low voltage coefficient. They are also beneficial due to long-term stability. [158] => [159] => ===Metal oxide film=== [160] => Metal-oxide film resistors are made of metal oxides which results in a higher operating temperature and greater stability and reliability than metal film. They are used in applications with high endurance demands. [161] => [162] => ===Wire wound=== [163] => [[File:KTSU resistors.jpg|thumb|right|High-power wire wound resistors used for [[dynamic braking]] on an electric railway car. Such resistors may dissipate many kilowatts for an extended length of time.]] [164] => [[File:Types of winding by Zureks.png|thumb|Types of windings in wire resistors: {{ordered list |common |[[bifilar winding|bifilar]] |common on a thin former |[[Ayrton–Perry winding|Ayrton–Perry]]}}]] [165] => [166] => Wirewound resistors are commonly made by winding a metal wire, usually [[nichrome]], around a ceramic, plastic, or fiberglass core. The ends of the wire are soldered or welded to two caps or rings, attached to the ends of the core. The assembly is protected with a layer of paint, molded plastic, or an [[Vitreous enamel|enamel]] coating baked at high temperature. These resistors are designed to withstand unusually high temperatures of up to 450 °C. Wire leads in low power wirewound resistors are usually between 0.6 and 0.8 mm in diameter and tinned for ease of soldering. For higher power wirewound resistors, either a ceramic outer case or an aluminum outer case on top of an insulating layer is used. If the outer case is ceramic, such resistors are sometimes described as "cement" resistors, though they do not actually contain any traditional [[Portland cement|cement]]. The aluminum-cased types are designed to be attached to a heat sink to dissipate the heat; the rated power is dependent on being used with a suitable heat sink, e.g., a 50 W power rated resistor overheats at a fraction of the power dissipation if not used with a heat sink. Large wirewound resistors may be rated for 1,000 watts or more. [167] => [168] => Because wirewound resistors are [[Electromagnetic coil|coils]] they have more undesirable [[Electromagnetic induction|inductance]] than other types of resistor. However, winding the wire in sections with alternately reversed direction can minimize inductance. Other techniques employ [[bifilar winding]], or a flat thin former (to reduce cross-section area of the coil). For the most demanding circuits, resistors with [[Ayrton–Perry winding]] are used. [169] => [170] => Applications of wirewound resistors are similar to those of composition resistors with the exception of high frequency applications. The high frequency response of wirewound resistors is substantially worse than that of a composition resistor. [171] => [172] => ===Metal foil resistor=== [173] => [[File:Metal foil resistor.png|thumb|Metal foil resistor]] [174] => [175] => In 1960, [[Felix Zandman]] and Sidney J. Stein{{cite journal |title=A New Precision Film Resistor Exhibiting Bulk Properties |year=1964 |doi=10.1109/TCP.1964.1135008|last1=Zandman |first1=F. |last2=Stein |first2=S. |journal=IEEE Transactions on Component Parts |volume=11 |issue=2 |pages=107–119 }} presented a development of resistor film of very high stability. [176] => [177] => The primary resistance element of a foil resistor is a chromium nickel alloy foil several [[micrometre|micrometers]] thick. Chromium nickel alloys are characterized by having a large electrical resistance (about 58 times that of copper), a small temperature coefficient and high resistance to oxidation. Examples are Chromel A and Nichrome V, whose typical composition is 80 Ni and 20 Cr, with a melting point of 1420 °C. When iron is added, the chromium nickel alloy becomes more ductile. The Nichrome and Chromel C are examples of an alloy containing iron. The composition typical of Nichrome is 60 Ni, 12 Cr, 26 Fe, 2 Mn and Chromel C, 64 Ni, 11 Cr, Fe 25. The melting temperature of these alloys are 1350 °C and 1390 °C, respectively.''Procedures in Experimental Physics'', John Strong, p. 546.{{full citation needed|date=December 2021}} [178] => [179] => Since their introduction in the 1960s, foil resistors have had the best precision and stability of any resistor available. One of the important parameters of stability is the temperature coefficient of resistance (TCR). The TCR of foil resistors is extremely low, and has been further improved over the years. One range of ultra-precision foil resistors offers a TCR of 0.14 ppm/°C, tolerance ±0.005%, long-term stability (1 year) 25 ppm, (3 years) 50 ppm (further improved 5-fold by hermetic sealing), stability under load (2000 hours) 0.03%, thermal EMF 0.1 μV/°C, noise −42 dB, voltage coefficient 0.1 ppm/V, inductance 0.08 μH, capacitance 0.5 pF.{{cite web|url=http://www.alpha-elec.co.jp/e_machine.html |title=Alpha Electronics Corp. Metal Foil Resistors |publisher=Alpha-elec.co.jp |access-date=2008-09-22}} [180] => [181] => The thermal stability of this type of resistor also has to do with the opposing effects of the metal's electrical resistance increasing with temperature, and being reduced by thermal expansion leading to an increase in thickness of the foil, whose other dimensions are constrained by a ceramic substrate.{{citation needed|date=July 2018}} [182] => [183] => ===Ammeter shunts=== [184] => An [[Shunt (electrical)#Use in current measuring|ammeter shunt]] is a special type of current-sensing resistor, having four terminals and a value in milliohms or even micro-ohms. Current-measuring instruments, by themselves, can usually accept only limited currents. To measure high currents, the current passes through the shunt across which the voltage drop is measured and interpreted as current. A typical shunt consists of two solid metal blocks, sometimes brass, mounted on an insulating base. Between the blocks, and soldered or brazed to them, are one or more strips of low [[Temperature coefficient of resistivity|temperature coefficient of resistance]] (TCR) [[manganin]] alloy. Large bolts threaded into the blocks make the current connections, while much smaller screws provide volt meter connections. Shunts are rated by full-scale current, and often have a voltage drop of 50 mV at rated current. Such meters are adapted to the shunt full current rating by using an appropriately marked dial face; no change need to be made to the other parts of the meter. [185] => [186] => ===Grid resistor=== [187] => In heavy-duty industrial high-current applications, a grid resistor is a large convection-cooled lattice of stamped metal alloy strips connected in rows between two electrodes. Such industrial grade resistors can be as large as a refrigerator; some designs can handle over 500 amperes of current, with a range of resistances extending lower than 0.04 ohms. They are used in applications such as [[dynamic braking]] and [[Load bank#Resistive load bank|load banking]] for [[Diesel locomotive|locomotives]] and trams, neutral grounding for industrial AC distribution, control loads for cranes and heavy equipment, load testing of generators and harmonic filtering for electric substations.[http://www.milwaukeeresistor.com/gridresistors.html "Grid Resistors: High Power/High Current"]. Milwaukee Resistor Corporation. Retrieved 14 May 2012. [188] => [189] => The term ''grid resistor'' is sometimes used to describe a resistor of any type connected to the [[control grid]] of a [[vacuum tube]]. This is not a resistor technology; it is an electronic circuit topology. [190] => [191] => ===Special varieties=== [192] => * [[Cermet]] [193] => * [[Phenolic resin|Phenolic]] [194] => * [[Tantalum]] [195] => * [[Water resistor]] [196] => [197] => ==Variable resistors== [198] => {{Main article|List of resistors}} [199] => [200] => ===Adjustable resistors=== [201] => A resistor may have one or more fixed tapping points so that the resistance can be changed by moving the connecting wires to different terminals. Some wirewound power resistors have a tapping point that can slide along the resistance element, allowing a larger or smaller part of the resistance to be used. [202] => [203] => Where continuous adjustment of the resistance value during operation of equipment is required, the sliding resistance tap can be connected to a knob accessible to an operator. Such a device is called a [[rheostat]] and has two terminals. [204] => [205] => ===Potentiometers=== [206] => [207] => [[File:Potentiometer cutaway drawing.png|thumb|Potentiometer with case cut away, showing parts: (''A'') shaft, (''B'') stationary carbon composition resistance element, (''C'') phosphor bronze wiper, (''D'') shaft attached to wiper, (''E, G'') terminals connected to ends of resistance element, (''F'') terminal connected to wiper.]] [208] => A [[potentiometer]] (colloquially, ''pot'') is a three-terminal resistor with a continuously adjustable tapping point controlled by rotation of a shaft or knob or by a linear slider.{{cite book [209] => | last1 = Mazda [210] => | first1 = F. F. [211] => | title = Discrete Electronic Components [212] => | publisher = CUP Archive [213] => | date = 1981 [214] => | pages = 57–61 [215] => | url = https://books.google.com/books?id=3qk8AAAAIAAJ&pg=PA57 [216] => | isbn = 0521234700 [217] => }} The name ''potentiometer'' comes from its function as an adjustable [[voltage divider]] to provide a variable [[potential]] at the terminal connected to the tapping point. Volume control in an audio device is a common application of a potentiometer. A typical low power potentiometer ''(see drawing)'' is constructed of a flat resistance element ''(B)'' of carbon composition, metal film, or conductive plastic, with a springy [[phosphor bronze]] wiper contact ''(C)'' which moves along the surface. An alternate construction is resistance wire wound on a form, with the wiper sliding axially along the coil. These have lower resolution, since as the wiper moves the resistance changes in steps equal to the resistance of a single turn. [218] => [219] => High-resolution multiturn potentiometers are used in precision applications. These have wire-wound resistance elements typically wound on a helical mandrel, with the wiper moving on a helical track as the control is turned, making continuous contact with the wire. Some include a conductive-plastic resistance coating over the wire to improve resolution. These typically offer ten turns of their shafts to cover their full range. They are usually set with dials that include a simple turns counter and a graduated dial, and can typically achieve three-digit resolution. Electronic analog computers used them in quantity for setting coefficients and delayed-sweep oscilloscopes of recent decades included one on their panels. [220] => [221] => [222] => File:Potentiometer.jpg|Typical panel mount potentiometer [223] => File:12 board mounted potentiometers.jpg|An assortment of small through-hole potentiometers designed for mounting on [[printed circuit board]]s. [224] => [225] => [226] => ===Resistance decade boxes=== [227] => {{Main article|Decade box}} [228] => [[File:Odporová dekáda KURBELWIDERSTAND (A).jpg|thumb|Resistance decade box]] [229] => A resistance decade box or resistor substitution box is a unit containing resistors of many values, with one or more mechanical switches which allow any one of various discrete resistances offered by the box to be dialed in. Usually the resistance is accurate to high precision, ranging from laboratory/calibration grade accuracy of 20 parts per million, to field grade at 1%. Inexpensive boxes with lesser accuracy are also available. All types offer a convenient way of selecting and quickly changing a resistance in laboratory, experimental and development work without needing to attach resistors one by one, or even stock each value. The range of resistance provided, the maximum resolution, and the accuracy characterize the box. For example, one box offers resistances from 0 to 100 megohms, maximum resolution 0.1 ohm, accuracy 0.1%.{{cite web|url=http://www.ietlabs.com/decaderes.html |title=Decade Box – Resistance Decade Boxes |publisher=Ietlabs.com |access-date=2008-09-22}} [230] => [231] => ===Special devices=== [232] => There are various devices whose resistance changes with various quantities. The resistance of NTC [[thermistor]]s exhibit a strong negative temperature coefficient, making them useful for measuring temperatures. Since their resistance can be large until they are allowed to heat up due to the passage of current, they are also commonly used to prevent excessive [[Inrush current|current surges]] when equipment is powered on. Similarly, the resistance of a [[humistor]] varies with humidity. One sort of photodetector, the [[photoresistor]], has a resistance which varies with illumination. [233] => [234] => The [[strain gauge]], invented by [[Edward E. Simmons]] and [[Arthur C. Ruge]] in 1938, is a type of resistor that changes value with applied strain. A single resistor may be used, or a pair (half bridge), or four resistors connected in a [[Wheatstone bridge]] configuration. The strain resistor is bonded with adhesive to an object that is subjected to [[Infinitesimal strain theory|mechanical strain]]. With the strain gauge and a filter, amplifier, and analog/digital converter, the strain on an object can be measured. [235] => [236] => A related but more recent invention uses a [[Quantum Tunnelling Composite]] to sense mechanical stress. It passes a current whose magnitude can vary by a factor of 1012 in response to changes in applied pressure. [237] => [238] => ==Measurement== [239] => The value of a resistor can be measured with an [[ohmmeter]], which may be one function of a [[multimeter]]. Usually, probes on the ends of test leads connect to the resistor. A simple ohmmeter may apply a voltage from a battery across the unknown resistor (with an internal resistor of a known value in series) producing a current which drives a [[Galvanometer|meter movement]]. The current, in accordance with [[Ohm's law]], is inversely proportional to the sum of the internal resistance and the resistor being tested, resulting in an analog meter scale which is very non-linear, calibrated from infinity to 0 ohms. A digital multimeter, using active electronics, may instead pass a specified current through the test resistance. The voltage generated across the test resistance in that case is linearly proportional to its resistance, which is measured and displayed. In either case the low-resistance ranges of the meter pass much more current through the test leads than do high-resistance ranges. This allows for the voltages present to be at reasonable levels (generally below 10 volts) but still measurable. [240] => [241] => Measuring low-value resistors, such as fractional-ohm resistors, with acceptable accuracy requires [[Four-terminal sensing|four-terminal connections]]. One pair of terminals applies a known, calibrated current to the resistor, while the other pair senses the voltage drop across the resistor. Some laboratory quality ohmmeters, milliohmmeters, and even some of the better digital multimeters sense using four input terminals for this purpose, which may be used with special test leads called [[Four-terminal sensing|Kelvin clips]]. Each of the two clips has a pair of jaws insulated from each other. One side of each clip applies the measuring current, while the other connections are only to sense the voltage drop. The resistance is again calculated using Ohm's Law as the measured voltage divided by the applied current. [242] => [243] => ==Standards== [244] => [245] => ===Production resistors=== [246] => Resistor characteristics are quantified and reported using various national standards. In the US, MIL-STD-202{{cite web |url=http://www.dscc.dla.mil/Downloads/MilSpec/Docs/MIL-STD-202/std202.pdf |title=Test method standard: electronic and electrical component parts |publisher=Department of Defense |url-status=dead |archive-url=https://web.archive.org/web/20150209025640/http://www.dscc.dla.mil/downloads/milspec/docs/mil-std-202/std202.pdf |archive-date=2015-02-09 }} contains the relevant test methods to which other standards refer. [247] => [248] => There are various standards specifying properties of resistors for use in equipment: [249] => * [[IEC 60062]] (IEC 62) / [[DIN 40825]] / [[BS 1852]] / [[IS 8186]] / [[JIS C 5062]] etc. ([[Resistor color code]], [[RKM code]], date code) [250] => * [[EIA RS-279]] / [[DIN 41429]] (Resistor color code) [251] => * [[IEC 60063]] (IEC 63) / [[JIS C 5063]] (Standard E series values) [252] => * MIL-PRF-26 [253] => * MIL-PRF-39007 (Fixed power, established reliability) [254] => * MIL-PRF-55342 (Surface-mount thick and thin film) [255] => * MIL-PRF-914 [256] => * MIL-R-11 [http://www.landandmaritime.dla.mil/Programs/MilSpec/ListDocs.aspx?BasicDoc=MIL-R-11 Standard Canceled] [257] => * MIL-R-39017 (Fixed, General Purpose, Established Reliability) [258] => * MIL-PRF-32159 (zero ohm jumpers) [259] => * UL 1412 (fusing and temperature limited resistors)[https://web.archive.org/web/20080210020811/http://ulstandardsinfonet.ul.com/scopes/scopes.asp?fn=1412.html Fusing Resistors and Temperature-Limited Resistors for Radio- and Television- Type Appliances UL 1412]. ulstandardsinfonet.ul.com [260] => [261] => There are other United States military procurement MIL-R- standards. [262] => [263] => ===Resistance standards=== [264] => The [[primary standard]] for resistance, the "mercury ohm" was initially defined in 1884 in as a column of mercury 106.3 cm long and {{nowrap|1 square millimeter}} in cross-section, at {{nowrap|0 degrees Celsius}}. Difficulties in precisely measuring the physical constants to replicate this standard result in variations of as much as 30 ppm. From 1900 the mercury ohm was replaced with a precision machined plate of [[manganin]].[http://nvl.nist.gov/pub/nistpubs/sp958-lide/063-065.pdf Stability of Double-Walled Manganin Resistors] {{Webarchive|url=https://web.archive.org/web/20061006125243/http://nvl.nist.gov/pub/nistpubs/sp958-lide/063-065.pdf |date=2006-10-06 }}. NIST.gov Since 1990 the international resistance standard has been based on the [[quantum Hall effect|quantized Hall effect]] discovered by [[Klaus von Klitzing]], for which he won the Nobel Prize in Physics in 1985.Klaus von Klitzing [http://nobelprize.org/nobel_prizes/physics/laureates/1985/klitzing-lecture.pdf The Quantized Hall Effect]. Nobel lecture, December 9, 1985. nobelprize.org [265] => [266] => Resistors of extremely high precision are manufactured for [[calibration]] and [[laboratory]] use. They may have four terminals, using one pair to carry an operating current and the other pair to measure the voltage drop; this eliminates errors caused by voltage drops across the lead resistances, because no charge flows through voltage sensing leads. It is important in small value resistors (100–0.0001 ohm) where lead resistance is significant or even comparable with respect to resistance standard value.{{cite web |url=http://www.tinsley.co.uk/products/standard-resistors/4737b.htm |title=Standard Resistance Unit Type 4737B |publisher=Tinsley.co.uk |access-date=2008-09-22 |url-status=dead |archive-url=https://web.archive.org/web/20080821154924/http://www.tinsley.co.uk/products/standard-resistors/4737b.htm |archive-date=2008-08-21 }} [267] => [268] => ==Resistor marking== [269] => {{Main article|Electronic color code}} [270] => [[File:ResistorColorCodeGuide.jpg|thumb|right|Wheel-based [[Radio Manufacturers Association|RMA]] Resistor Color Code guide. Circa 1945–1950.]] [271] => [272] => Axial resistor cases are usually tan, brown, blue, or green (though other colors are occasionally found as well, such as dark red or dark gray), and display three to six colored stripes that indicate resistance (and by extension tolerance), and may include bands to indicate the temperature coefficient and reliability class. In four-striped resistors, the first two stripes represent the first two digits of the resistance in [[ohm]]s, the third represents a [[Multiplication#Notation and terminology|multiplier]], and the fourth the tolerance (which if absent, denotes ±20%). For five- and six- striped resistors the third band is the third digit, the fourth is the multiplier and the fifth is the tolerance; a sixth stripe represents the temperature coefficient. The power rating of the resistor is usually not marked and is deduced from its size. [273] => [274] => [[Surface-mount]] resistors are marked numerically. [275] => [276] => Early 20th century resistors, essentially uninsulated, were dipped in paint to cover their entire body for color-coding. This base color represented the first digit. A second color of paint was applied to one end of the element to represent a second digit, and a color dot (or band) in the middle provided the third digit. The rule was "body, tip, dot", providing two significant digits for value and the decimal multiplier, in that sequence. Default tolerance was ±20%. Closer-tolerance resistors had silver (±10%) or gold-colored (±5%) paint on the other end. [277] => [278] => ===Preferred values=== [279] => {{See also|E-series of preferred numbers}} [280] => Early resistors were made in more or less arbitrary round numbers; a series might have 100, 125, 150, 200, 300, etc.{{cite web |title=1940 Catalog – page 60 – Resistors |url=http://www.radioshackcatalogs.com/html/1940/hr060.html |website=[[RadioShack]] |access-date=11 July 2017 |archive-url=https://web.archive.org/web/20170711160604/http://www.radioshackcatalogs.com/html/1940/hr060.html |archive-date=11 July 2017}} Early power wirewound resistors, such as brown vitreous-enameled types, were made with a system of preferred values like some of those mentioned here. Resistors as manufactured are subject to a certain percentage [[Engineering tolerance|tolerance]], and it makes sense to manufacture values that correlate with the tolerance, so that the actual value of a resistor overlaps slightly with its neighbors. Wider spacing leaves gaps; narrower spacing increases manufacturing and inventory costs to provide resistors that are more or less interchangeable. [281] => [282] => A logical scheme is to produce resistors in a range of values which increase in a [[geometric progression]], so that each value is greater than its predecessor by a fixed multiplier or percentage, chosen to match the tolerance of the range. For example, for a tolerance of ±20% it makes sense to have each resistor about 1.5 times its predecessor, covering a decade in 6 values. More precisely, the factor used is 1.4678 ≈ 10^{1/6}, giving values of 1.47, 2.15, 3.16, 4.64, 6.81, 10 for the 1–10-decade (a decade is a range increasing by a factor of 10; 0.1–1 and 10–100 are other examples); these are rounded in practice to 1.5, 2.2, 3.3, 4.7, 6.8, 10; followed by 15, 22, 33, ... and preceded by ... 0.47, 0.68, 1. This scheme has been adopted as the [[E6 (number series)|E6 series]] of the [[International Electrotechnical Commission|IEC]] 60063 [[preferred number]] values. There are also '''E12''', '''E24''', '''E48''', '''E96''' and '''E192''' series for components of progressively finer resolution, with 12, 24, 48, 96, and 192 different values within each decade. The actual values used are in the [[International Electrotechnical Commission|IEC]] 60063 lists of preferred numbers. [283] => [284] => A resistor of 100 ohms ±20% would be expected to have a value between 80 and 120 ohms; its E6 neighbors are 68 (54–82) and 150 (120–180) ohms. A sensible spacing, E6 is used for ±20% components; E12 for ±10%; E24 for ±5%; E48 for ±2%, E96 for ±1%; E192 for ±0.5% or better. Resistors are manufactured in values from a few milliohms to about a gigaohm in IEC60063 ranges appropriate for their tolerance. Manufacturers may sort resistors into tolerance-classes based on measurement. Accordingly, a selection of 100 ohms resistors with a tolerance of ±10%, might not lie just around 100 ohm (but no more than 10% off) as one would expect (a bell-curve), but rather be in two groups – either between 5 and 10% too high or 5 to 10% too low (but not closer to 100 ohm than that) because any resistors the factory had measured as being less than 5% off would have been marked and sold as resistors with only ±5% tolerance or better. When designing a circuit, this may become a consideration. This process of sorting parts based on post-production measurement is known as "binning", and can be applied to other components than resistors (such as speed grades for CPUs). [285] => [286] => ===SMT resistors=== [287] => [[File:Zero ohm resistors cropped.jpg|thumb|This image shows four surface-mount resistors (the component at the upper left is a [[capacitor]]) including two [[zero-ohm resistor]]s. Zero-ohm links are often used instead of wire links, so that they can be inserted by a resistor-inserting machine. Their resistance is negligible. ]] [288] => [289] => [[Surface-mount technology|Surface mounted]] resistors of larger sizes (metric [[Surface-mount technology#Packages|1608]] and above) are printed with numerical values in a code related to that used on axial resistors. Standard-tolerance [[surface-mount technology|surface-mount technology (SMT)]] resistors are marked with a three-digit code, in which the first two digits are the first two [[significant digit]]s of the value and the third digit is the power of ten (the number of zeroes). For example: [290] => [291] => * 334 = 33 × 104 Ω = 330 kΩ [292] => * 222 = 22 × 102 Ω = 2.2 kΩ [293] => * 473 = 47 × 103 Ω = 47 kΩ [294] => * 105 = 10 × 105 Ω = 1 MΩ [295] => [296] => Resistances less than 100 Ω are written: 100, 220, 470. The final zero represents ten to the power zero, which is 1. For example: [297] => [298] => * 100 = 10 × 100 Ω = 10 Ω [299] => * 220 = 22 × 100 Ω = 22 Ω [300] => [301] => Sometimes these values are marked as 10 or 22 to prevent a mistake. [302] => [303] => Resistances less than 10 Ω have 'R' to indicate the position of the decimal point ([[radix point]]). For example: [304] => [305] => * 4R7 = 4.7 Ω [306] => * R300 = 0.30 Ω [307] => * 0R22 = 0.22 Ω [308] => * 0R01 = 0.01 Ω [309] => [310] => 000 and 0000 sometimes appear as values on surface-mount [[zero-ohm link]]s, since these have (approximately) zero resistance. [311] => [312] => More recent surface-mount resistors are too small, physically, to permit practical markings to be applied. [313] => [314] => ===Precision resistor markings=== [315] => [316] => Many precision resistors, including surface mount and axial-lead types, are marked with a four-digit code. The first three digits are the significant figures and the fourth is the power of ten. For example: [317] => [318] => * 1001 = 100 × 101 Ω = 1.00 kΩ [319] => * 4992 = 499 × 102 Ω = 49.9 kΩ [320] => * 1000 = 100 × 100 Ω = 100 Ω [321] => [322] => Axial-lead precision resistors often use color code bands to represent this four-digit code. [323] => [324] => ==== {{anchor|3-char-resistor-marking-code}}EIA-96 marking ==== [325] => [326] => The former EIA-96 marking system now included in [[IEC 60062:2016]] is a more compact marking system intended for physically small high-precision resistors. It uses a two-digit code plus a letter (a total of three alphanumeric characters) to indicate 1% resistance values to three significant digits.[https://eepower.com/resistor-guide/resistor-standards-and-codes/resistor-smd-code/ "Chapter 2 - Resistor standards and codes"]. The two digits (from "01" to "96") are a code that indicates one of the 96 "positions" in the standard [[E96 series]] of 1% resistor values. The uppercase letter is a code that indicates a [[power of ten]] multiplier. For example, the marking "01C" represents 10 kOhm; "10C" represents 12.4 kOhm; "96C" represents 97.6 kOhm.[https://www.bourns.com/pdfs/CRP0603.pdf "CRP0603 Series - Precision Chip Resistors"]. p. 3.[http://kiloohm.info/eia96-resistor/96C "Online calculator - EIA-96 SMD resistor"].[https://www.electricaltechnology.org/2013/07/how-to-calculate-or-find-value-of-smd.html "SMD Resistor Codes: How to Find the Value of SMD Resistors"].[https://www.ttelectronics.com/TTElectronics/media/ProductFiles/ApplicationNotes/TN004-Methods-for-Marking-Values-on-Resistors.pdf "Marking Codes used on Welwyn Chip Resistors"]. p. 2.[https://www.electronics-notes.com/articles/electronic_components/resistors/smt-smd-resistor-codes-markings.php "Surface Mount Resistor: codes & markings"]. [327] => [328] => {| [329] => | [330] => {| class="wikitable" style="float:left; margin-right:2em;" [331] => !Code [332] => !Series [333] => !colspan="7"|Letter [334] => |- [335] => !Digits [336] => !E96 [337] => !Y / S [338] => !X / R [339] => !A [340] => !B / H [341] => !C [342] => !D [343] => !E [344] => |- [345] => !01 [346] => !1.00 [347] => |1R00||10R0||100R||1K00||10K0||100K||1M00 [348] => |- [349] => !02 [350] => !1.02 [351] => |1R02||10R2||102R||1K02||10K2||102K||1M02 [352] => |- [353] => !03 [354] => !1.05 [355] => |1R05||10R5||105R||1K05||10K5||105K||1M05 [356] => |- [357] => !04 [358] => !1.07 [359] => |1R07||10R7||107R||1K07||10K7||107K||1M07 [360] => |- [361] => !05 [362] => !1.10 [363] => |1R10||11R0||110R||1K10||11K0||110K||1M10 [364] => |- [365] => !06 [366] => !1.13 [367] => |1R13||11R3||113R||1K13||11K3||113K||1M13 [368] => |- [369] => !07 [370] => !1.15 [371] => |1R15||11R5||115R||1K15||11K5||115K||1M15 [372] => |- [373] => !08 [374] => !1.18 [375] => |1R18||11R8||118R||1K18||11K8||118K||1M18 [376] => |- [377] => !09 [378] => !1.21 [379] => |1R21||12R1||121R||1K21||12K1||121K||1M21 [380] => |- [381] => !10 [382] => !1.24 [383] => |1R24||12R4||124R||1K24||12K4||124K||1M24 [384] => |- [385] => !11 [386] => !1.27 [387] => |1R27||12R7||127R||1K27||12K7||127K||1M27 [388] => |- [389] => !12 [390] => !1.30 [391] => |1R30||13R0||130R||1K30||13K0||130K||1M30 [392] => |- [393] => !13 [394] => !1.33 [395] => |1R33||13R3||133R||1K33||13K3||133K||1M33 [396] => |- [397] => !14 [398] => !1.37 [399] => |1R37||13R7||137R||1K37||13K7||137K||1M37 [400] => |- [401] => !15 [402] => !1.40 [403] => |1R40||14R0||140R||1K40||14K0||140K||1M40 [404] => |- [405] => !16 [406] => !1.43 [407] => |1R43||14R3||143R||1K43||14K3||143K||1M43 [408] => |- [409] => !17 [410] => !1.47 [411] => |1R47||14R7||147R||1K47||14K7||147K||1M47 [412] => |- [413] => !18 [414] => !1.50 [415] => |1R50||15R0||150R||1K50||15K0||150K||1M50 [416] => |- [417] => !19 [418] => !1.54 [419] => |1R54||15R4||154R||1K54||15K4||154K||1M54 [420] => |- [421] => !20 [422] => !1.58 [423] => |1R58||15R8||158R||1K58||15K8||158K||1M58 [424] => |- [425] => !21 [426] => !1.62 [427] => |1R62||16R2||162R||1K62||16K2||162K||1M62 [428] => |- [429] => !22 [430] => !1.65 [431] => |1R65||16R5||165R||1K65||16K5||165K||1M65 [432] => |- [433] => !23 [434] => !1.69 [435] => |1R69||16R9||169R||1K69||16K9||169K||1M69 [436] => |- [437] => !24 [438] => !1.74 [439] => |1R74||17R4||174R||1K74||17K4||174K||1M74 [440] => |- [441] => !25 [442] => !1.78 [443] => |1R78||17R8||178R||1K78||17K8||178K||1M78 [444] => |- [445] => !26 [446] => !1.82 [447] => |1R82||18R2||182R||1K82||18K2||182K||1M82 [448] => |- [449] => !27 [450] => !1.87 [451] => |1R87||18R7||187R||1K87||18K7||187K||1M87 [452] => |- [453] => !28 [454] => !1.91 [455] => |1R91||19R1||191R||1K91||19K1||191K||1M91 [456] => |- [457] => !29 [458] => !1.96 [459] => |1R96||19R6||196R||1K96||19K6||196K||1M96 [460] => |- [461] => !30 [462] => !2.00 [463] => |2R00||20R0||200R||2K00||20K0||200K||2M00 [464] => |- [465] => !31 [466] => !2.05 [467] => |2R05||20R5||205R||2K05||20K5||205K||2M05 [468] => |- [469] => !32 [470] => !2.10 [471] => |2R10||21R0||210R||2K10||21K0||210K||2M10 [472] => |- [473] => !33 [474] => !2.15 [475] => |2R15||21R5||215R||2K15||21K5||215K||2M15 [476] => |- [477] => !34 [478] => !2.21 [479] => |2R21||22R1||221R||2K21||22K1||221K||2M21 [480] => |- [481] => !35 [482] => !2.26 [483] => |2R26||22R6||226R||2K26||22K6||226K||2M26 [484] => |- [485] => !36 [486] => !2.32 [487] => |2R32||23R2||232R||2K32||23K2||232K||2M32 [488] => |- [489] => !37 [490] => !2.37 [491] => |2R37||23R7||237R||2K37||23K7||237K||2M37 [492] => |- [493] => !38 [494] => !2.43 [495] => |2R43||24R3||243R||2K43||24K3||243K||2M43 [496] => |- [497] => !39 [498] => !2.49 [499] => |2R49||24R9||249R||2K49||24K9||249K||2M49 [500] => |- [501] => !40 [502] => !2.55 [503] => |2R55||25R5||255R||2K55||25K5||255K||2M55 [504] => |- [505] => !41 [506] => !2.61 [507] => |2R61||26R1||261R||2K61||26K1||261K||2M61 [508] => |- [509] => !42 [510] => !2.67 [511] => |2R67||26R7||267R||2K67||26K7||267K||2M67 [512] => |- [513] => !43 [514] => !2.74 [515] => |2R74||27R4||274R||2K74||27K4||274K||2M74 [516] => |- [517] => !44 [518] => !2.80 [519] => |2R80||28R0||280R||2K80||28K0||280K||2M80 [520] => |- [521] => !45 [522] => !2.87 [523] => |2R87||28R7||287R||2K87||28K7||287K||2M87 [524] => |- [525] => !46 [526] => !2.94 [527] => |2R94||29R4||294R||2K94||29K4||294K||2M94 [528] => |- [529] => !47 [530] => !3.01 [531] => |3R01||30R1||301R||3K01||30K1||301K||3M01 [532] => |- [533] => !48 [534] => !3.09 [535] => |3R09||30R9||309R||3K09||30K9||309K||3M09 [536] => |} [537] => | [538] => {| class="wikitable" style="float: right; margin-right: 2em;" [539] => !Code [540] => !Series [541] => !colspan="7"|Letter [542] => |- [543] => !Digits [544] => !E96 [545] => !Y / S [546] => !X / R [547] => !A [548] => !B / H [549] => !C [550] => !D [551] => !E [552] => |- [553] => !49 [554] => !3.16 [555] => |3R16||31R6||316R||3K16||31K6||316K||3M16 [556] => |- [557] => !50 [558] => !3.24 [559] => |3R24||32R4||324R||3K24||32K4||324K||3M24 [560] => |- [561] => !51 [562] => !3.32 [563] => |3R32||33R2||332R||3K32||33K2||332K||3M32 [564] => |- [565] => !52 [566] => !3.40 [567] => |3R40||34R0||340R||3K40||34K0||340K||3M40 [568] => |- [569] => !53 [570] => !3.48 [571] => |3R48||34R8||348R||3K48||34K8||348K||3M48 [572] => |- [573] => !54 [574] => !3.57 [575] => |3R57||35R7||357R||3K57||35K7||357K||3M57 [576] => |- [577] => !55 [578] => !3.65 [579] => |3R65||36R5||365R||3K65||36K5||365K||3M65 [580] => |- [581] => !56 [582] => !3.74 [583] => |3R74||37R4||374R||3K74||37K4||374K||3M74 [584] => |- [585] => !57 [586] => !3.83 [587] => |3R83||38R3||383R||3K83||38K3||383K||3M83 [588] => |- [589] => !58 [590] => !3.92 [591] => |3R92||39R2||392R||3K92||39K2||392K||3M92 [592] => |- [593] => !59 [594] => !4.02 [595] => |4R02||40R2||402R||4K02||40K2||402K||4M02 [596] => |- [597] => !60 [598] => !4.12 [599] => |4R12||41R2||412R||4K12||41K2||412K||4M12 [600] => |- [601] => !61 [602] => !4.22 [603] => |4R22||42R2||422R||4K22||42K2||422K||4M22 [604] => |- [605] => !62 [606] => !4.32 [607] => |4R32||43R2||432R||4K32||43K2||432K||4M32 [608] => |- [609] => !63 [610] => !4.42 [611] => |4R42||44R2||442R||4K42||44K2||442K||4M42 [612] => |- [613] => !64 [614] => !4.53 [615] => |4R53||45R3||453R||4K53||45K3||453K||4M53 [616] => |- [617] => !65 [618] => !4.64 [619] => |4R64||46R4||464R||4K64||46K4||464K||4M64 [620] => |- [621] => !66 [622] => !4.75 [623] => |4R75||47R5||475R||4K75||47K5||475K||4M75 [624] => |- [625] => !67 [626] => !4.87 [627] => |4R87||48R7||487R||4K87||48K7||487K||4M87 [628] => |- [629] => !68 [630] => !4.99 [631] => |4R99||49R9||499R||4K99||49K9||499K||4M99 [632] => |- [633] => !69 [634] => !5.11 [635] => |5R11||51R1||511R||5K11||51K1||511K||5M11 [636] => |- [637] => !70 [638] => !5.23 [639] => |5R23||52R3||523R||5K23||52K3||523K||5M23 [640] => |- [641] => !71 [642] => !5.36 [643] => |5R36||53R6||536R||5K36||53K6||536K||5M36 [644] => |- [645] => !72 [646] => !5.49 [647] => |5R49||54R9||549R||5K49||54K9||549K||5M49 [648] => |- [649] => !73 [650] => !5.62 [651] => |5R62||56R2||562R||5K62||56K2||562K||5M62 [652] => |- [653] => !74 [654] => !5.76 [655] => |5R76||57R6||576R||5K76||57K6||576K||5M76 [656] => |- [657] => !75 [658] => !5.90 [659] => |5R90||59R0||590R||5K90||59K0||590K||5M90 [660] => |- [661] => !76 [662] => !6.04 [663] => |6R04||60R4||604R||6K04||60K4||604K||6M04 [664] => |- [665] => !77 [666] => !6.19 [667] => |6R19||61R9||619R||6K19||61K9||619K||6M19 [668] => |- [669] => !78 [670] => !6.34 [671] => |6R34||63R4||634R||6K34||63K4||634K||6M34 [672] => |- [673] => !79 [674] => !6.49 [675] => |6R49||64R9||649R||6K49||64K9||649K||6M49 [676] => |- [677] => !80 [678] => !6.65 [679] => |6R65||66R5||665R||6K65||66K5||665K||6M65 [680] => |- [681] => !81 [682] => !6.81 [683] => |6R81||68R1||681R||6K81||68K1||681K||6M81 [684] => |- [685] => !82 [686] => !6.98 [687] => |6R98||69R8||698R||6K98||69K8||698K||6M98 [688] => |- [689] => !83 [690] => !7.15 [691] => |7R15||71R5||715R||7K15||71K5||715K||7M15 [692] => |- [693] => !84 [694] => !7.32 [695] => |7R32||73R2||732R||7K32||73K2||732K||7M32 [696] => |- [697] => !85 [698] => !7.50 [699] => |7R50||75R0||750R||7K50||75K0||750K||7M50 [700] => |- [701] => !86 [702] => !7.68 [703] => |7R68||76R8||768R||7K68||76K8||768K||7M68 [704] => |- [705] => !87 [706] => !7.87 [707] => |7R87||78R7||787R||7K87||78K7||787K||7M87 [708] => |- [709] => !88 [710] => !8.06 [711] => |8R06||80R6||806R||8K06||80K6||806K||8M06 [712] => |- [713] => !89 [714] => !8.25 [715] => |8R25||82R5||825R||8K25||82K5||825K||8M25 [716] => |- [717] => !90 [718] => !8.45 [719] => |8R45||84R5||845R||8K45||84K5||845K||8M45 [720] => |- [721] => !91 [722] => !8.66 [723] => |8R66||86R6||866R||8K66||86K6||866K||8M66 [724] => |- [725] => !92 [726] => !8.87 [727] => |8R87||88R7||887R||8K87||88K7||887K||8M87 [728] => |- [729] => !93 [730] => !9.09 [731] => |9R09||90R9||909R||9K09||90K9||909K||9M09 [732] => |- [733] => !94 [734] => !9.31 [735] => |9R31||93R1||931R||9K31||93K1||931K||9M31 [736] => |- [737] => !95 [738] => !9.53 [739] => |9R53||95R3||953R||9K53||95K3||953K||9M53 [740] => |- [741] => !96 [742] => !9.76 [743] => |9R76||97R6||976R||9K76||97K6||976K||9M76 [744] => |} [745] => |} [746] => {{clear}} [747] => [748] => ===Industrial type designation=== [749] => {| class="wikitable" style="float: left; margin-right: 2em;" [750] => |+Power Rating at 70 °C [751] => !Type no. [752] => !Power
rating
(watts) [753] => ![[MIL-R-11]]
style [754] => ![[MIL-R-39008]]
style [755] => |- style="text-align: center;" [756] => |BB||{{frac|1|8}}||RC05||RCR05 [757] => |- style="text-align: center;" [758] => |CB||{{frac|1|4}}||RC07||RCR07 [759] => |- style="text-align: center;" [760] => |EB||{{frac|1|2}}||RC20||RCR20 [761] => |- style="text-align: center;" [762] => |GB||1||RC32||RCR32 [763] => |- style="text-align: center;" [764] => |HB||2||RC42||RCR42 [765] => |- style="text-align: center;" [766] => |GM||3||-||- [767] => |- style="text-align: center;" [768] => |HM||4||-||- [769] => |} [770] => {| class="wikitable" style="float: left;" [771] => |+Tolerance code [772] => |- style="text-align: center;" [773] => !style="width: 75px;"|Industrial type designation [774] => !style="width: 50px;"|Tolerance [775] => !style="width: 75px;"|MIL designation [776] => |- style="text-align: center;" [777] => |5||±5%||J [778] => |- style="text-align: center;" [779] => |2||±20%||M [780] => |- style="text-align: center;" [781] => |1||±10%||K [782] => |- style="text-align: center;" [783] => | -||±2%||G [784] => |- style="text-align: center;" [785] => | -||±1%||F [786] => |- style="text-align: center;" [787] => | -||±0.5%||D [788] => |- style="text-align: center;" [789] => | -||±0.25%||C [790] => |- style="text-align: center;" [791] => | -||±0.1%||B [792] => |} [793] => {{clear}} [794] => [795] => Steps to find out the resistance or capacitance values:Maini, A. K. (2008), ''Electronics and Communications Simplified'', 9th ed., Khanna Publications. {{ISBN|817409217X}} [796] => [797] => # First two letters gives the power dissipation capacity. [798] => # Next three digits gives the resistance value. [799] => ## First two digits are the significant values [800] => ## Third digit is the multiplier. [801] => # Final digit gives the tolerance. [802] => [803] => If a resistor is coded: [804] => * EB1041: power dissipation capacity = 1/2 watts, resistance value = {{val|10|e=4}}±10% = between {{val|9|e=4}} ohms and {{val|11|e=4}} ohms. [805] => * CB3932: power dissipation capacity = 1/4 watts, resistance value = {{val|39|e=3}}±20% = between {{val|31.2|e=3}} and {{val|46.8|e=3}} ohms. [806] => [807] => == Common usage patterns == [808] => [809] => There are several common usage patterns that resistors are commonly configured in.{{cite book |title=Electronics for Beginners |chapter=Basic Resistor Circuit Patterns |date=2020 |chapter-url=https://link.springer.com/chapter/10.1007/978-1-4842-5979-5_9 |doi=10.1007/978-1-4842-5979-5_9 |last1=Bartlett |first1=Jonathan |pages=129–144 |isbn=978-1-4842-5978-8 |s2cid=226539488 }} [810] => [811] => === Current Limiting === [812] => [813] => Resistors are commonly used to limit the amount of current flowing through a circuit. Many circuit components (such as LEDs) require the current flowing through them to be limited, but do not themselves limit the amount of current. Therefore, oftentimes resistors will be added to prevent overcurrent situations. Additionally, oftentimes circuits do not need the amount of current that would be otherwise flowing through them, so resistors can be added to limit the power consumption of such circuits. [814] => [815] => === Voltage Divider === [816] => {{main|Voltage divider}} [817] => [818] => Oftentimes circuits need to provide various reference voltages for other circuits (such as voltage comparators). A fixed voltage can be obtained by taking two resistors in series between two other fixed voltages (such as the source voltage and ground). The terminal between the two resistors will be at a voltage that is between the two voltages, at a linear distance based on the relative resistances of the two resistors. For instance, if a 200 ohm resistor and a 400 ohm resistor are placed in series between 6V and 0V, the terminal between them will be at 4V. [819] => [820] => === Pull-down and Pull-up Resistors === [821] => {{main|Pull-up resistor}} [822] => [823] => When a circuit is not connected to power, the voltage of that circuit is not zero but undefined (it can be influenced by previous voltages or the environment). A pull-up or pull-down resistor provides a voltage for a circuit when it is otherwise disconnected (such as when a button is not pushed down or a transistor is not active). A pull-up resistor connects the circuit to a high positive voltage (if the circuit requires a high positive default voltage) and a pull-down resistor connects the circuit to a low voltage or ground (if the circuit requires a low default voltage). The resistor value must be high enough so that, when the circuit is active, the voltage source it is attached to does not over influence the function of the circuit, but low enough so that it "pulls" quickly enough when the circuit is deactivated, and does not significantly alter the voltage from the source value. [824] => [825] => ==Electrical and thermal noise== [826] => {{Main article|Noise (electronics)}} [827] => [828] => In amplifying faint signals, it is often necessary to minimize [[electronic noise]], particularly in the first stage of amplification. As a dissipative element, even an ideal resistor naturally produces a randomly fluctuating voltage, or noise, across its terminals. This [[Johnson–Nyquist noise]] is a fundamental noise source which depends only upon the temperature and resistance of the resistor, and is predicted by the [[fluctuation–dissipation theorem]]. Using a larger value of resistance produces a larger voltage noise, whereas a smaller value of resistance generates more current noise, at a given temperature. [829] => [830] => The thermal noise of a practical resistor may also be larger than the theoretical prediction and that increase is typically frequency-dependent. Excess noise of a practical resistor is observed only when current flows through it. This is specified in unit of μV/V/decade – μV of noise per volt applied across the resistor per decade of frequency. The μV/V/decade value is frequently given in dB so that a resistor with a noise index of 0 dB exhibits 1 μV (rms) of excess noise for each volt across the resistor in each frequency decade. Excess noise is thus an example of [[Flicker noise|1/''f'' noise]]. Thick-film and carbon composition resistors generate more excess noise than other types at low frequencies. Wire-wound and thin-film resistors are often used for their better noise characteristics. Carbon composition resistors can exhibit a noise index of 0 dB while bulk metal foil resistors may have a noise index of −40 dB, usually making the excess noise of metal foil resistors insignificant.{{cite book [831] => | title = Audio Noise Reduction Through the Use of Bulk Metal Foil Resistors – "Hear the Difference" [832] => | url = http://www.c-c-i.com/sites/default/files/vse-an00.pdf [833] => | access-date = 2009-08-03 [834] => | archive-date = 2013-01-19 [835] => | archive-url = https://web.archive.org/web/20130119120843/http://www.c-c-i.com/sites/default/files/vse-an00.pdf [836] => | url-status = dead [837] => }}, Application note AN0003, Vishay Intertechnology Inc, 12 July 2005. Thin film surface mount resistors typically have lower noise and better thermal stability than thick film surface mount resistors. Excess noise is also size-dependent: in general, excess noise is reduced as the physical size of a resistor is increased (or multiple resistors are used in parallel), as the independently fluctuating resistances of smaller components tend to average out. [838] => [839] => While not an example of "noise" per se, a resistor may act as a [[thermocouple]], producing a small DC voltage differential across it due to the [[thermoelectric effect]] if its ends are at different temperatures. This induced DC voltage can degrade the precision of [[instrumentation amplifier]]s in particular. Such voltages appear in the junctions of the resistor leads with the circuit board and with the resistor body. Common metal film resistors show such an effect at a magnitude of about 20 μV/°C. Some carbon composition resistors can exhibit thermoelectric offsets as high as 400 μV/°C, whereas specially constructed resistors can reduce this number to 0.05 μV/°C. In applications where the thermoelectric effect may become important, care has to be taken to mount the resistors horizontally to avoid temperature gradients and to mind the air flow over the board.{{cite book [840] => | title = Op Amp Applications Handbook [841] => | author = Jung, Walt [842] => | url = http://www.analog.com/library/analogDialogue/archives/39-05/op_amp_applications_handbook.html [843] => | chapter = Chapter 7 – Hardware and Housekeeping Techniques [844] => | chapter-url = http://www.analog.com/library/analogDialogue/archives/39-05/Web_Ch7_final_J.pdf [845] => | page = 7.11 [846] => | isbn = 0-7506-7844-5 [847] => | year = 2005 [848] => | publisher = Newnes [849] => }} [850] => [851] => ==Failure modes== [852] => The failure rate of resistors in a properly designed circuit is low compared to other electronic components such as semiconductors and electrolytic capacitors. Damage to resistors most often occurs due to overheating when the average power delivered to it greatly exceeds its ability to dissipate heat (specified by the resistor's ''power rating''). This may be due to a fault external to the circuit but is frequently caused by the failure of another component (such as a transistor that shorts out) in the circuit connected to the resistor. Operating a resistor too close to its power rating can limit the resistor's lifespan or cause a significant change in its resistance. A safe design generally uses overrated resistors in power applications to avoid this danger. [853] => [854] => Low-power thin-film resistors can be damaged by long-term high-voltage stress, even below maximum specified voltage and below maximum power rating. This is often the case for the startup resistors feeding a [[switched-mode power supply]] integrated circuit.{{Citation needed|date=July 2011}} [855] => [856] => When overheated, carbon-film resistors may decrease or increase in resistance.{{cite web [857] => | title = Electronic components – resistors [858] => | work = Inspector's Technical Guide [859] => | publisher = US Food and Drug Administration [860] => | date = 1978-01-16 [861] => | url = https://www.fda.gov/ora/Inspect_ref/itg/itg31.html [862] => | access-date = 2008-06-11 |archive-url = https://web.archive.org/web/20080403111045/https://www.fda.gov/ora/Inspect_ref/itg/itg31.html |archive-date = 2008-04-03}} [863] => Carbon film and composition resistors can fail (open circuit) if running close to their maximum dissipation. This is also possible but less likely with metal film and wirewound resistors. [864] => [865] => There can also be failure of resistors due to mechanical stress and adverse environmental factors including humidity. If not enclosed, wirewound resistors can corrode. [866] => [867] => Surface mount resistors have been known to fail due to the ingress of sulfur into the internal makeup of the resistor. This sulfur chemically reacts with the silver layer to produce non-conductive silver sulfide. The resistor's impedance goes to infinity. Sulfur resistant and anti-corrosive resistors are sold into automotive, industrial, and military applications. ASTM B809 is an industry standard that tests a part's susceptibility to sulfur. [868] => [869] => An alternative failure mode can be encountered where large value resistors are used (hundreds of kilohms and higher). Resistors are not only specified with a maximum power dissipation, but also for a maximum voltage drop. Exceeding this voltage causes the resistor to degrade slowly reducing in resistance. The voltage dropped across large value resistors can be exceeded before the power dissipation reaches its limiting value. Since the maximum voltage specified for commonly encountered resistors is a few hundred volts, this is a problem only in applications where these voltages are encountered. [870] => [871] => Variable resistors can also degrade in a different manner, typically involving poor contact between the wiper and the body of the resistance. This may be due to dirt or corrosion and is typically perceived as "crackling" as the [[contact resistance]] fluctuates; this is especially noticed as the device is adjusted. This is similar to crackling caused by poor contact in switches, and like switches, potentiometers are to some extent self-cleaning: running the wiper across the resistance may improve the contact. Potentiometers which are seldom adjusted, especially in dirty or harsh environments, are most likely to develop this problem. When self-cleaning of the contact is insufficient, improvement can usually be obtained through the use of [[contact cleaner]] (also known as "tuner cleaner") spray. The crackling noise associated with turning the shaft of a dirty potentiometer in an audio circuit (such as the volume control) is greatly accentuated when an undesired DC voltage is present, often indicating the failure of a DC blocking capacitor in the circuit. [872] => [873] => ==See also== [874] => {{Portal|Electronics}} [875] => * [[Circuit design]] [876] => * [[Dummy load]] [877] => * [[Electrical impedance]] [878] => * [[High value resistors (electronics)]] [879] => * [[Iron-hydrogen resistor]] [880] => * [[Piezoresistive effect]] [881] => * [[Shot noise]] [882] => * [[Thermistor]] [883] => * [[Trimmer (electronics)]] [884] => [885] => ==References== [886] => {{Reflist}} [887] => [888] => ==External links== [889] => {{Commons category multi|Resistors|Resistors (SMD)}} [890] => {{wikibooks [891] => | 1 = Electronics [892] => | 2 = Resistors [893] => | 3 = Resistors [894] => }} [895] => {{Wiktionary}} [896] => * [https://web.archive.org/web/20110401175312/http://www.ese.upenn.edu/rca/calcjs.html Color Coded Resistance Calculator] - University of Pennsylvania [897] => * [https://web.archive.org/web/20130407011352/http://www.aikenamps.com/ResistorNoise.htm Resistor Types – Does It Matter?] - Aiken Amps [898] => * [http://www.analog.com/library/analogDialogue/archives/31-1/Ask_Engineer.html Difference between types of resistors] - Analog Devices [899] => * [https://www.vishay.com/docs/28771/basics.pdf Basics of Linear Fixed Resistors] - Vishay [900] => * [https://web.archive.org/web/20110715110844/http://www.powerstandards.com/4terminal.htm 4-terminal resistors – How ultra-precise resistors work] - PSL [901] => * [https://www.sound-au.com/pots.htm Beginners' Guide to Potentiometers] - ESP [902] => [903] => {{Electronic component}} [904] => {{Digital electronics}} [905] => {{Authority control}} [906] => [907] => [[Category:Electrical components]] [908] => [[Category:Electric heating]] [909] => [[Category:Resistive components]] [] => )
good wiki

Resistor

A resistor is an electrical component that limits or controls the flow of electric current in a circuit. It is one of the most commonly used components in electronic circuits, as it helps to regulate the voltage and current levels within a circuit.

More about us

About

It is one of the most commonly used components in electronic circuits, as it helps to regulate the voltage and current levels within a circuit. Resistors are passive components, meaning they do not produce or amplify electrical signals. They are typically made of materials that have high resistivity, such as carbon, metal, or ceramic, which allows them to impede the flow of electricity. The resistance of a resistor is measured in ohms (Ω) and determines how much current will flow through it for a given voltage. Resistors come in various shapes and sizes, and there are different types of resistors suitable for different applications. The most common type is the axial resistor, which has a cylindrical shape with colored bands indicating the resistor's resistance value. Other types include surface mount resistors, which are smaller and used for compact circuits, and variable resistors, also known as potentiometers, which can be adjusted to change the resistance value. The main function of a resistor is to reduce the current flowing through a circuit or divide the voltage across components. They are often used to protect sensitive components from excessive current flow, adjust signal levels, and set the biasing of active components such as transistors. Resistors can also be used in combination to form voltage dividers, filter circuits, and timing circuits. In addition to their electrical properties, resistors also have various physical characteristics that need to be considered, including their power rating, tolerance, and temperature coefficient. The power rating indicates the maximum power the resistor can handle without getting damaged, while the tolerance specifies the range within which the actual resistance value may deviate from the stated value. The temperature coefficient indicates how the resistance changes with temperature. Overall, resistors play a crucial role in electronics and are fundamental to the functioning of a wide range of devices, from simple household appliances to complex computer systems.

Expert Team

Vivamus eget neque lacus. Pellentesque egauris ex.

Award winning agency

Lorem ipsum, dolor sit amet consectetur elitorceat .

10 Year Exp.

Pellen tesque eget, mauris lorem iupsum neque lacus.

You might be interested in

Ampere

Ampere is the unit of electric current in the International System of Units (SI).

Capacitance

Capacitance is the ability of a body or system to store an electric charge.

Electronics

Electronics is the science and technology of studying, designing, and manufacturing devices that use the flow of electrons to perform electrical functions.

Kelvin

Kelvin is a unit of temperature widely used in the scientific field.

Laboratory

A laboratory is a controlled environment used by scientists, researchers, and technicians to conduct experiments, carry out scientific investigations, and analyze samples.

Micrometre

A micrometre, also known as a micrometer, is a unit of length in the metric system.

Multimeter

A multimeter, also known as a VOM (Volt-Ohm-Milliammeter), is an electronic measuring instrument used to measure electrical variables such as voltage, current, and resistance.

Thermocouple

A thermocouple is a temperature-measuring device that consists of two different conductors joined together at one end.

Watt

Watt is the SI unit of power, named after the Scottish engineer James Watt.